IEC57

最小值

Minimum

典型值

Typical

最大值

Maximum

单位

unit

输出电流(峰值) Output current (peak)

0.5

-

8.0

A

输入电源电压（直流）Input supply   voltage (DC)

15

24/36/48

50

VDC

控制信号输入电流Control signal input current

6

10

16

mA

控制信号接口电平Control signal interface level

4.5

5

28

Vdc

OC输出上拉电压OC output   pull-up voltage

5

-

24

Vdc

Ether-CAT通讯频率Ether-CAT   communication frequency

-

100

-

MHz

绝缘电阻Insulation resistance

100

-

-

MΩ

使用环境

Environment

场合Occasion

不能放在其它发热的设备旁，要避免粉尘、油雾、腐蚀性气体，湿度太大及强振动场所，禁止有可燃气体和导电灰尘；

It should not be placed next to other heating   equipment. Dust, oil mist, corrosive gas, excessive humidity and strong   vibration should be avoided. Combustible gas and conductive dust should not   be allowed.

温度Temperature

-10℃ ～ +50℃

湿度Humidity

40 ～ 90%RH

振动Vibration

5.9m/s2MAX

防护Protection

整机IP65等级    IP65

保存温度Storage   temperature

-20℃～60℃

使用海拔Altitude

1000米以下Below   1000 meters

重量Weight

1.2KG

GND

直流电源地DC   power ground

+VDC

直流电源正极，供电电压范围：直流15~50Vdc，推荐24Vdc或36Vdc工作。

DC   power supply positive, power supply voltage range: DC 15~50Vdc, recommended   24Vdc or 36Vdc work.

IN1+

高速信号：脉冲上升沿有效；in1高电平时4.5～28Vdc，低电平时0～0.5V。为了可靠响应脉冲信号，脉冲宽度应大于1.5μs。

High-speed signal: pulse rising edge   is valid; in1 high level is 4.5~28Vdc, low level is 0~0.5V. In order to   respond reliably to pulse signals, the pulse width should be greater than 1.5   μ s.

IN1-

IN2+

高速信号：脉冲上升沿有效；in2高电平时4.5～28Vdc，低电平时0～0.5V。为了可靠响应脉冲信号，脉冲宽度应大于1.5μs。

High-speed signal: pulse rising edge   is valid; in2 high level is 4.5~28Vdc, low level is 0~0.5V. In order to   respond reliably to pulse signals, the pulse width should be greater than 1.5   μ s. 

IN2-

IN3+

低速信号：脉冲上升沿有效；in3高电平时4.5～28Vdc，低电平时0～0.5V。为了可靠响应脉冲信号，脉冲宽度应大于5μs。

Low speed signal: pulse rising edge   is valid; in3 high level is 4.5~28Vdc, low level is 0~0.5V. In order to   respond reliably to pulse signals, the pulse width should be greater than 5 μ   s.

IN3-

OUT+

输出信号，一般做报警输出用，OC射极开路输出，需要上拉电平，最大上拉电压为24V。

Output signal, generally used for   alarm output, OC emitter open output, requires pull-up level, the maximum   pull-up voltage is 24V.

OUT-

15V

15V电压输出，输出电流最大10mA，预留

15V voltage output, output current up   to 10mA, reserved

AIN

一路0-5V模拟量输入，预留

One way 0-5V analog input, reserved

GND

EGND，5V电压参考负极，预留

EGND, 5V voltage reference negative,   reserved

RS232-TX

串口RS232 发送端，TTL-3.3V电平，设置或配置参数用，预留

Serial RS232 transmitter, TTL-3.3V   level, setting or configuration parameters, reserved

RS232-RX

串口RS232 接收端，TTL-3.3V电平，设置或配置参数用，预留

Serial   RS232 transmitter, TTL-3.3V level, setting or configuration parameters,   reserved

5V

提供电压5V，电流50mA，预留

Supply   voltage 5V, current 50mA, reserved

1

TX+

Ether CAT 数据发送正端

Ether   CAT data transmission positive end

Ether CAT IN

2

TX-

Ether CAT 数据发送负端

Ether   CAT data transmission negative end

3

RX+

Ether CAT 数据接收正端

Ether   CAT data reception positive end

4

RX-

Ether CAT 数据接收负端

Ether   CAT data reception negative end

5

NC

不连接，预留Not connected, reserved

6

NC

不连接，预留Not connected, reserved

7

NC

不连接，预留Not connected, reserved

8

NC

不连接，预留Not connected, reserved

1

TX+

Ether CAT 数据发送正端

Ether   CAT data transmission positive end

Ether CAT  OUT

2

TX-

Ether CAT 数据发送负端

Ether   CAT data transmission negative end

3

RX+

Ether CAT 数据接收正端

Ether   CAT data reception positive end

4

RX-

Ether CAT 数据接收负端

Ether   CAT data reception negative end

5

NC

不连接，预留Not connected, reserved

6

NC

不连接，预留Not connected, reserved

7

NC

不连接，预留Not connected, reserved

8

NC

不连接，预留Not connected, reserved